|
VOLV_LO
|
 |
« on: March 21, 2004, 01:27:09 AM » |
|
 heres an image of them, hook up info to come... :ph34r: :ph34r: |
|
|
« Last Edit: September 13, 2012, 10:29:44 PM by Hydros »
|
Logged
|
|
|
|
|
VOLV_LO
|
|
« Reply #1 on: March 23, 2004, 12:48:24 PM » |
|
I will add some pics later but here is the instructions in my words with out pics..
HOW SOLENOID BANKS WORK
Solenoids are one of those things you need to keep an eye on. Ford Starter Solenoids are the most commonly used. FORD SW-3 are the most reccommended for this application or VICTORY LAP 19-6250-6 (grey in color)
SOLENOIDS are Gateways that let power pass from your batteries to your PUMP MOTORS. Each one must CLOSE AND OPEN in sequence to work properly. WHEN ALL ARE CLOSED AT THE SAME TIME, your pumps will run becasue the power can now pass from your batteries to your pump motors. If one solenoid in a bank is stuck open when you hit the switch and close the other two the power CANNOT pass to your motors, therefor your pumps will not spin and you will hear a CLICK-CLICK sound. THE CLICKING is the mechanical part of your other solenoids moving when you are hitting the switch. When ONE SOLENOID in your bank is STUCK CLOSED your pump will run fine as the other two can stop the power from getting to your pumps.
ITS WHEN ALL THREE ARE STUCK CLOSED THAT you are running to your QUICK DISCONNECT to stop the pumps from spinning.
TESTING THEM WITH A CONTINUITY TESTER (OR LIGHT BULB)
1 - Disconnect the cable from your battery to your solenoid bank that is in question.
2 - Make sure your QUICK DISCONNECT GROUND is plugged in and your switches work this bank.
3 - Start at the first solenoid, probe on either side of a solenoid, have a friend hit the switch that activates this bank. If the tester beeps or the light lights up only when the switch is held on, the solenoid is good. if the beep stays on regardless on the switch the solenoid is stuck CLOSED, if the light wont light up nor the tester beep regardless of the switching, the SOLENOID IS STUCK OPEN. and is bad
Do this to each solenoid in the bank and REPLACE ALL BAD SOLENOIDS NOW!!!!
VISUAL AID TO FOLLOW.
|
|
|
|
|
Logged
|
|
|
|
|
VOLV_LO
|
|
« Reply #2 on: March 23, 2004, 12:49:06 PM » |
|
|
|
|
« Last Edit: September 13, 2012, 10:30:17 PM by Hydros »
|
Logged
|
|
|
|
|
LowriderUK
|
|
« Reply #3 on: April 26, 2004, 08:49:33 AM » |
|
So is it necessary to have three solenoids per pumps, or is that just triple protection?
My two pump system only had one soleniod for each pump?
Hydro newbie, can ya tell?
|
|
|
|
|
Logged
|
I'm a hydro newbie...PLEASE DONT LAUGH!!![/size]
1979 Oldsmobile Cutlass Supreme....jus' crying out for 'The Treatment'!
Shame I'm a 13 hour flight away from my garage.....THAT SUCKS![/b][/font] 
|
|
|
|
Guest
Guest
|
|
« Reply #4 on: April 26, 2004, 09:25:51 AM » |
|
So is it necessary to have three solenoids per pumps, or is that just triple protection?
My two pump system only had one soleniod for each pump?
Hydro newbie, can ya tell? How many batteries to each pump? |
|
|
|
|
Logged
|
|
|
|
|
LowriderUK
|
|
« Reply #5 on: April 26, 2004, 09:40:14 AM » |
|
How many batteries to each pump? Just two, connected for 24volts, supplying both pumps... I guess multiple solenoids in a bank are for higher voltages, like 72/96v? |
|
|
|
|
Logged
|
I'm a hydro newbie...PLEASE DONT LAUGH!!![/size]
1979 Oldsmobile Cutlass Supreme....jus' crying out for 'The Treatment'!
Shame I'm a 13 hour flight away from my garage.....THAT SUCKS![/b][/font]
|
|
|
|
Hydros
|
|
« Reply #6 on: April 26, 2004, 09:26:14 PM » |
|
On thing I always try to do is to post info that I have done and what works for me. I can't answer your question, because I run my solenoids different than what other do. I run only four solenoids in parrell (spell check) and series with 6 batterys. http://hydros.biz/forum/index.php?showtopic=47This info is not yet completed. |
|
|
|
|
Logged
|
Was this information helpful?
What information would you like to see?
Post your comments, questions and suggestions here.
Send email to: tjjjc2 @ yahoo. com (use no spaces)
|
|
|
|
Hydros
|
|
« Reply #7 on: April 26, 2004, 09:29:25 PM » |
|
Later when I run 8-10 batteries I may only use two solenoids. These will be a totally different type that no one else uses. If I find this type to be a problem I will run two banks of three or may go to three banks of two. I favor the three banks of two for 8 or more batteries.
|
|
|
|
« Last Edit: April 26, 2004, 09:38:35 PM by Hydros »
|
Logged
|
Was this information helpful?
What information would you like to see?
Post your comments, questions and suggestions here.
Send email to: tjjjc2 @ yahoo. com (use no spaces)
|
|
|
|
juicdmonte
|
|
« Reply #8 on: December 06, 2005, 06:35:44 PM » |
|
did you ever test your 'alternative' solenoids at higher voltages?
|
|
|
|
|
Logged
|
|
|
|
|
Hydros
|
|
« Reply #9 on: December 06, 2005, 07:10:14 PM » |
|
Yes!!! It was a monster, the flash was too intense to look at. The amps to the switch were so much I had to run a solenoid for it too. see this thread http://hydros.biz/forum/index.php?topic=205.0 |
|
|
|
« Last Edit: September 30, 2012, 12:58:32 PM by Hydros »
|
Logged
|
Was this information helpful?
What information would you like to see?
Post your comments, questions and suggestions here.
Send email to: tjjjc2 @ yahoo. com (use no spaces)
|
|
|
|
