hydros.biz Lowrider hydraulics information
November 26, 2024, 01:50:08 PM *
Welcome, Guest. Please login or register.

Login with username, password and session length
News: Forum restoration complete! Bug hunt in progress!  Smiley
 
   Home   Help Search Login Register  
Pages: [1]
  Print  
Author Topic: My car, some info. 60" is the goal.  (Read 3669 times)
0 Members and 6 Guests are viewing this topic.
Hydros
Administrator
Expert Member
*****
Offline Offline

Posts: 569



View Profile
« on: July 10, 2004, 03:26:15 PM »

The goal is to get approx. 60" using 8 batteries, or 7.5" a battery.

Car was purchased already reinforced. It appeared to have been a hopper and for side to side use. - Story goes that the car was first owned by a hydraulic shop that hopped it. It was sold to Mr.Payne, and then I got it via ebay, it was a damn good deal, equipped with spokes, and 4 pumps with aircraft hydraulics. I had a system of using two different ebay users accounts and accidentally bid against myself, I might have won the car for less than $1,300. but got it for $1,500 still a good deal.

When I got it, the car needed a lot of work. I could only hop a few inches using two pumps. I have not touched a lifted car in over 20 years. Meaning, I plan to make a lot of mistakes, learn a lot and share on what not to do, so that other can learn too.
« Last Edit: March 16, 2013, 03:06:50 AM by Hydros » Logged

Was this information helpful?
What information would you like to see?
Post your comments, questions and suggestions here.



Send email to: tjjjc2 @ yahoo. com (use no spaces)
Hydros
Administrator
Expert Member
*****
Offline Offline

Posts: 569



View Profile
« Reply #1 on: March 06, 2005, 01:12:30 AM »

3-5-05 almost 16 months after I bought the car I finally got a real chance to work on it. After patching up some frame cracks, cut out the old battery tray and installed a real tray, I am 98% done with the tray. This week the hold down studs and cross bars go in.

It's got 10 group 31's going 5 and 5 sideways. This does not allow me legal lengths using LRM rules for metal. I seen this on a car at BMH, it was Pinkys. All ten batteries just fit with about 1/4" to spare.

One thought is to use a Pesco pump for the rear of this hopper... Different or what. Overall, the hoppers about 15% completed.
« Last Edit: March 16, 2013, 03:09:04 AM by Hydros » Logged

Was this information helpful?
What information would you like to see?
Post your comments, questions and suggestions here.



Send email to: tjjjc2 @ yahoo. com (use no spaces)
Hydros
Administrator
Expert Member
*****
Offline Offline

Posts: 569



View Profile
« Reply #2 on: April 20, 2005, 11:24:43 AM »

update:
4-10-05

It did hop approx 26" 7 batteries, unknown front coils, 3 1/2 ton rears (trying to break them in for the front) BMH pistion pump.  Before this a ball joint busted and just after this the 3,000 PSI check valve and cheap fitting busted.

* regal.jpg (27.1 KB - downloaded 245 times.)
« Last Edit: March 16, 2013, 03:10:09 AM by Hydros » Logged

Was this information helpful?
What information would you like to see?
Post your comments, questions and suggestions here.



Send email to: tjjjc2 @ yahoo. com (use no spaces)
Hydros
Administrator
Expert Member
*****
Offline Offline

Posts: 569



View Profile
« Reply #3 on: March 16, 2013, 01:14:27 AM »

UPDATE almost 8 years later...

With all the different new innovations and cirrus cars, it has been decided to forget about hopping the highest, it is now " per battery. This way, if a rider wants to hop higher, add more volts.

This IMO is considered to be the new frontier, instead of finding a way to adding another battery to get higher, clean out the trunk and use as fewer batteries as possible to do some decent street action.


http://hydros.biz/forum/index.php?topic=254.0
« Last Edit: March 16, 2013, 01:21:52 AM by Hydros » Logged

Was this information helpful?
What information would you like to see?
Post your comments, questions and suggestions here.



Send email to: tjjjc2 @ yahoo. com (use no spaces)
Pages: [1]
  Print  
 
Jump to:  

Powered by MySQL Powered by PHP Powered by SMF 1.1.20 | SMF © 2013, Simple Machines Valid XHTML 1.0! Valid CSS!